Products

Standard MaxCell

  STANDARD MAXCELL

Melt Point of 419°FA versatile solution for the complex problems faced by today’s engineers, contractors and network providers. Manufactured from internally designed and produced materials, this model yields superior performance over existing rigid innerduct.

Standard MaxCell is the primary product line used in common outside plant applications, including long lines, under-bridge; road, river and rail borings; under streets and all the way to building entrance points. In dense multiple cables and multiple MaxCell pack installations where the conduit path is not clear to surface markers, Standard MaxCell is often partnered with Detectable MaxCell so that path or service interruption points can be easily located.

Standard MaxCell is available for conduit sizes ranging from 1" to 4", and in 1-, 2- and 3-cell configurations — giving you the flexibility to choose the right product for your system and applications.

  Features & Advantages
  • Melt point of 419°F — almost 2X of HDPE
  • Resistant to ground chemicals and petroleum products
  • Pre-lubed for lower friction during MaxCell and cable installation
  • Pull tape included

  4" 3-CELL

4 Inch 3-CELLFor use in 4" or larger conduits, the 4" 3-Cell product is designed to hold larger backbone cables up to 1.5" in diameter in each cell. Up to two packs can be placed in a 4" conduit.

  • Standard color is green
  • Color-coded pull tapes are preinstalled
  • Factory lubricated
  Application Guide

This product was designed for use in 4" or larger ducts. Multiple combinations of large and medium cable sizes are applicable. Since larger cable applications are anticipated, the number of cables and packs that can be placed is reduced; therefore, a smaller number of cables is available.

MIN CONDUIT ID
MAX # OF PACKS
MAX # OF CABLES
MAX CABLE DIAMETER PER CELL
REC. PULL LENGTH*
MAX PULL LENGTH*
4" 2 6 1.5" 1,250' 2,000'
5" 3 9 1.5" 1,250' 2,000'
6" 4 12 1.5" 1,250' 2,000'

* Use of OFNR cable may result in reduced pulling lengths. Designers should make every effort to conform to industry standards with regard to distances between any two pull points (generally 600 to 1,000 feet), number of bends (maximum of two 90 degree bends or a total of 180 degrees) between any two pull points, and proofing of conduit pathway using appropriately sized mandrels (normally ¼ to ½ inch less than the inside diameter of the conduit).

  Part Numbers
STD. COLOR
FOOTAGE (FEET)
STANDARD PRODUCT (MXC)
DETECTABLE PRODUCT (MXD)
PLENUM PRODUCT (MXP)
RISER PRODUCT (MXR)
Green (GR) 250 MXC4003XX250 MXD4003XX250 MXP4003XX250 MXR4003XX250
500-999 MXC4003XX500 MXD4003XX500 MXP4003XX500 MXR4003XX500
1,000-2,649 MXC4003XX1000 MXD4003XX1000 MXP4003XX1000 MXR4003XX1000
2,650-5,299 MXC4003XX2650 MXD4003XX2650 MXP4003XX2650 MXR4003XX2650
5,300-9,999 MXC4003XX5300 MXD4003XX5300 MXP4003XX5300 MXR4003XX5300
10,000 MXC4003XX10000 MXD4003XX10000 MXP4003XX10000 MXR4003XX10000
  Reel Sizes & Weights
DESCRIPTION
STD. PRODUCT LENGTH
REEL SIZE
TYPE OF REEL
TARE WEIGHT OF REEL
REEL WT. W/ STD. PRODUCT LENGTH
4" 3-Cell
Standard / Riser / Plenum
MXC4003
Product Wt:
107.5 lbs/1,000ft
500' 33"H x 15"W Composite 60 lbs 114 lbs
1,000' 33"H x 15"W Composite 60 lbs 168 lbs
2,650' 48"H x 22"W Steel 78 lbs 340 lbs
5,300' 72"H x 22"W Steel 88 lbs 658 lbs
10,000' 72"H x 30"W Steel 106 lbs 1,181 lbs

For non-standard length inquries, please contact customer service.

  3" 3-CELL

3 Inch 3-CELLFor use in 3" or larger conduits, the 3" 3-Cell product is designed to hold cables up to 1.05" in diameter in each cell. Up to 3 packs can be placed in a 4" conduit.

  • Standard colors are black, blue or red
  • Color-coded pull tapes are preinstalled
  • Factory lubricated
  Application Guide

This product was designed for use in 3" or larger ducts. Multiple combinations of large, medium and smaller cable sizes are applicable and anticipated.

MIN CONDUIT ID
MAX # OF PACKS
MAX # OF CABLES
MAX CABLE DIAMETER PER CELL
REC. PULL LENGTH*
MAX PULL LENGTH*
3" 2 6 1.05" 1,250' 2,000'
4" 3 9 1.05" 1,250' 2,000'
5" 4 12 1.05" 1,250' 2,000'
6" 5 15 1.05" 1,250' 2,000'

* Use of OFNR cable may result in reduced pulling lengths. Designers should make every effort to conform to industry standards with regard to distances between any two pull points (generally 600 to 1,000 feet), number of bends (maximum of two 90 degree bends or a total of 180 degrees) between any two pull points, and proofing of conduit pathway using appropriately sized mandrels (normally ¼ to ½ inch less than the inside diameter of the conduit).

  Part Numbers
STD. COLOR
FOOTAGE (FEET)
STANDARD PRODUCT (MXC)
DETECTABLE PRODUCT (MXD)
PLENUM PRODUCT (MXP)
RISER PRODUCT (MXR)
Black (BK)
or Blue (BL)
or Red (RD)
250 MXC3456XX250 MXD3456XX250 MXP3456XX250 MXR3456XX250
500-999 MXC3456XX500 MXD3456XX500 MXP3456XX500 MXR3456XX500
1,000-2,649 MXC3456XX1000 MXD3456XX1000 MXP3456XX1000 MXR3456XX1000
2,650-5,299 MXC3456XX2650 MXD3456XX2650 MXP3456XX2650 MXR3456XX2650
5,300-9,999 MXC3456XX5300 MXD3456XX5300 MXP3456XX5300 MXR3456XX5300
10,000 MXC3456XX10000 MXD3456XX10000 MXP3456XX10000 MXR3456XX10000
  Reel Sizes & Weights
DESCRIPTION
STD. PRODUCT LENGTH
REEL SIZE
TYPE OF REEL
TARE WEIGHT OF REEL
REEL WT. W/ STD. PRODUCT LENGTH
3" 3-Cell
Standard / Riser / Plenum
MXC3456
Product Wt:
88.5 lbs/1,000ft
500' 33"H x 15"W Composite 60 lbs 104 lbs
1,000' 33"H x 15"W Composite 60 lbs 149 lbs
2,650' 33"H x 22"W Composite 85 lbs 320 lbs
5,300' 48"H x 22"W Steel 78 lbs 525 lbs
10,000' 72"H x 30"W Steel 106 lbs 991 lbs

For non-standard length inquries, please contact customer service.

  2" 3-CELL

2 Inch 3-CELLFor use in 2" conduits, the 2" 3-Cell product is designed to hold three cables up to 0.85" in diameter in each cell.

  • Standard color is yellow
  • Color-coded pull tapes are preinstalled
  • Factory lubricated
  Application Guide

This product was designed for use in 2" ducts where three cables are being placed.

MIN CONDUIT ID
MAX # OF PACKS
MAX # OF CABLES
MAX CABLE DIAMETER PER CELL
REC. PULL LENGTH*
MAX PULL LENGTH*
2" 1 3 .85" 800' 1,500'

* Use of OFNR cable may result in reduced pulling lengths. Designers should make every effort to conform to industry standards with regard to distances between any two pull points (generally 600 to 1,000 feet), number of bends (maximum of two 90 degree bends or a total of 180 degrees) between any two pull points, and proofing of conduit pathway using appropriately sized mandrels (normally ¼ to ½ inch less than the inside diameter of the conduit).

  Part Numbers
STD. COLOR
FOOTAGE (FEET)
STANDARD PRODUCT (MXC)
DETECTABLE PRODUCT (MXD)
PLENUM PRODUCT (MXP)
RISER PRODUCT (MXR)
Yellow (YL) 250 MXC2003XX250 MXD2003XX250 MXP2003XX250 MXR2003XX250
500-999 MXC2003XX500 MXD2003XX500 MXP2003XX500 MXR2003XX500
1,000-2,649 MXC2003XX1000 MXD2003XX1000 MXP2003XX1000 MXR2003XX1000
2,650-5,299 MXC2003XX2650 MXD2003XX2650 MXP2003XX2650 MXR2003XX2650
5,300-9,999 MXC2003XX5300 MXD2003XX5300 MXP2003XX5300 MXR2003XX5300
10,000 MXC2003XX10000 MXD2003XX10000 MXP2003XX10000 MXR2003XX10000
  Reel Sizes & Weights
DESCRIPTION
STD. PRODUCT LENGTH
REEL SIZE
TYPE OF REEL
TARE WEIGHT OF REEL
REEL WT. W/ STD. PRODUCT LENGTH
2" 3-Cell
Standard / Riser / Plenum
MXC2003
Product Wt:
76 lbs/1,000ft
500' 33"H x 15"W Composite 60 lbs 98 lbs
1,000' 33"H x 15"W Composite 60 lbs 136 lbs
2,650' 33"H x 22"W Composite 85 lbs 287 lbs
5,300' 48"H x 22"W Steel 78 lbs 458 lbs
10,000' 72"H x 22"W Steel 88 lbs 848 lbs

For non-standard length inquries, please contact customer service.

  2" 2-CELL

2 Inch 2-CELLFor use in 2" conduits, the 2" 2-Cell product is designed to hold two cables up to 0.85" in diameter in each cell. It's ideal for overlay when one cable exists in a 2" conduit.

  • Standard color is black
  • Color-coded pull tapes are preinstalled
  • Factory lubricated
  Application Guide

This product was designed for use in 2" ducts where two cables are being placed.

MIN CONDUIT ID
MAX # OF PACKS
MAX # OF CABLES
MAX CABLE DIAMETER PER CELL
REC. PULL LENGTH*
MAX PULL LENGTH*
2" 1 2 .85" 800' 1,500'

* Use of OFNR cable may result in reduced pulling lengths. Designers should make every effort to conform to industry standards with regard to distances between any two pull points (generally 600 to 1,000 feet), number of bends (maximum of two 90 degree bends or a total of 180 degrees) between any two pull points, and proofing of conduit pathway using appropriately sized mandrels (normally ¼ to ½ inch less than the inside diameter of the conduit).

  Part Numbers
STD. COLOR
FOOTAGE (FEET)
STANDARD PRODUCT (MXC)
DETECTABLE PRODUCT (MXD)
PLENUM PRODUCT (MXP)
RISER PRODUCT (MXR)
Black (BK) 250 MXC2002XX250 MXD2002XX250 MXP2002XX250 MXR2002XX250
500-999 MXC2002XX500 MXD2002XX500 MXP2002XX500 MXR2002XX500
1,000-2,649 MXC2002XX1000 MXD2002XX1000 MXP2002XX1000 MXR2002XX1000
2,650-5,299 MXC2002XX2650 MXD2002XX2650 MXP2002XX2650 MXR2002XX2650
5,300-9,999 MXC2002XX5300 MXD2002XX5300 MXP2002XX5300 MXR2002XX5300
10,000 MXC2002XX10000 MXD2002XX10000 MXP2002XX10000 MXR2002XX10000
  Reel Sizes & Weights
DESCRIPTION
STD. PRODUCT LENGTH
REEL SIZE
TYPE OF REEL
TARE WEIGHT OF REEL
REEL WT. W/ STD. PRODUCT LENGTH
2" 2-Cell
Standard / Riser / Plenum
MXC2002
Product Wt:
51.5 lbs/1,000ft
500' 33"H x 15"W Composite 60 lbs 86 lbs
1,000' 33"H x 15"W Composite 60 lbs 112 lbs
2,650' 33"H x 22"W Composite 85 lbs 222 lbs
5,300' 48"H x 22"W Steel 78 lbs 328 lbs
10,000' 72"H x 22"W Steel 88 lbs 603 lbs

For non-standard length inquries, please contact customer service.

  2" 1-CELL

2 Inch 1-CELLFor use in 1.5" and 2" conduits, the 2" 1-Cell product is designed to hold cables up to 0.85" in diameter in each cell.

  • Standard color is white
  • Color-coded pull tapes are preinstalled
  • Factory lubricated
  Application Guide

This product was designed for use in 1.5" and 2" ducts. It is designed to deploy an additional cable in a confined small conduit or innerduct.

MIN CONDUIT ID
MAX # OF PACKS
MAX # OF CABLES
MAX CABLE DIAMETER PER CELL
REC. PULL LENGTH*
MAX PULL LENGTH*
1.5" + 1 1 .85" 800' 1,500'

* Use of OFNR cable may result in reduced pulling lengths. Designers should make every effort to conform to industry standards with regard to distances between any two pull points (generally 600 to 1,000 feet), number of bends (maximum of two 90 degree bends or a total of 180 degrees) between any two pull points, and proofing of conduit pathway using appropriately sized mandrels (normally ¼ to ½ inch less than the inside diameter of the conduit).

  Part Numbers
STD. COLOR
FOOTAGE (FEET)
STANDARD PRODUCT (MXC)
DETECTABLE PRODUCT (MXD)
PLENUM PRODUCT (MXP)
RISER PRODUCT (MXR)
White (WH) 250 MXC2001XX250 MXD2001XX250 MXP2001XX250 MXR2001XX250
500-999 MXC2001XX500 MXD2001XX500 MXP2001XX500 MXR2001XX500
1,000-2,649 MXC2001XX1000 MXD2001XX1000 MXP2001XX1000 MXR2001XX1000
2,650-5,299 MXC2001XX2650 MXD2001XX2650 MXP2001XX2650 MXR2001XX2650
5,300-9,999 MXC2001XX5300 MXD2001XX5300 MXP2001XX5300 MXR2001XX5300
10,000 MXC2001XX10000 MXD2001XX10000 MXP2001XX10000 MXR2001XX10000
  Reel Sizes & Weights
DESCRIPTION
STD. PRODUCT LENGTH
REEL SIZE
TYPE OF REEL
TARE WEIGHT OF REEL
REEL WT. W/ STD. PRODUCT LENGTH
2" 1-Cell
Standard / Riser / Plenum
MXC2001
Product Wt:
28 lbs/1,000ft
500' 33"H x 15"W Composite 60 lbs 74 lbs
1,000' 33"H x 15"W Composite 60 lbs 88 lbs
2,650' 33"H x 15"W Composite 60 lbs 135 lbs
5,300' 33"H x 22"W Composite 85 lbs 234 lbs
10,000' 48"H x 22"W Steel 78 lbs 335 lbs

For non-standard length inquries, please contact customer service.

  DOWNLOAD THIS PAGE